281 silicon mos fets (small signal) 2SK0620 (2sk620) silicon n-channel mos fet for switching features high-speed switching mini-type package, allowing downsizing of the sets and automatic insertion through the tape/magazine packing. absolute maximum ratings (ta = 25c) parameter drain to source breakdown voltage gate to source voltage drain current max drain current allowable power dissipation channel temperature storage temperature symbol v dss v gso i d i dp p d t ch t stg ratings 50 8 100 200 150 150 ? 55 to +150 unit v v ma ma mw c c electrical characteristics (ta = 25c) parameter drain to source cut-off current gate to source leakage current drain to source breakdown voltage gate threshold voltage drain to source on-resistance forward transfer admittance input capacitance (common source) output capacitance (common source) reverse transfer capacitance (common source) turn-on time turn-off time symbol i dss i gss v dss v th r ds(on) | y fs | c iss c oss c rss t on * t off * conditions v ds = 10v, v gs = 0 v gs = 8v, v ds = 0 i d = 100 a, v gs = 0 i d = 100 a, v ds = v gs i d = 20ma, v gs = 5v i d = 20ma, v ds = 5v, f = 1khz v ds = 5v, v gs = 0, f = 1mhz v dd = 5v, v gs = 0 to 5v, r l = 200 ? v dd = 5v, v gs = 5 to 0v, r l = 200 ? * t on , t off measurement circuit min 50 1.5 20 typ 30 10 20 unit a na v v ? ms pf pf pf ns ns max 10 50 3.5 50 15 5 1 1: gate jedec: to-236 2: source eiaj: sc-59 3: drain mini type package (3-pin) 2.8 +0.2 ? 0.3 1.5 +0.25 ? 0.05 0.650.15 0.650.15 3 1 2 0.95 0.95 1.90.2 0.4 +0.1 ? 0.05 1.1 +0.2 ? 0.1 0.8 0.40.2 0 to 0.1 0.16 +0.1 ? 0.06 1.45 0.1 to 0.3 2.9 +0.2 ? 0.05 v out v dd = 5v v gs = 5v 50 ? 200 ? 100 f v in 90% 10% 10% 90% v out t on t off marking symbol: 3n internal connection g d s note) the part number in the parenthesis shows conventional part number. unit: mm
282 silicon mos fets (small signal) p d ? ta i d ? v ds | y fs | ? v gs c iss , c oss , c rss ? v ds i d ? v gs r ds(on) ? v gs v in ? i o 2SK0620 0 160 40 120 80 140 20 100 60 0 240 200 160 120 80 40 ambient temperature ta ( ? c ) allowable power dissipation p d ( mw ) 012 10 8 26 4 0 120 100 80 60 40 20 v gs =6.0v 5.5v 5.0v 4.5v 3.5v 2.5v 3.0v 4.0v ta=25 ? c drain to source voltage v ds ( v ) drain current i d ( ma ) 012 10 8 26 4 0 60 50 40 30 20 10 v ds =5v ta=25 ? c gate to source voltage v gs ( v ) forward transfer admittance |y fs | ( ms ) 1 3 10 30 100 0 12 10 8 6 4 2 v gs =0 f=1mhz ta=25 ? c c iss c oss c rss drain to source voltage v ds ( v ) input capacitance ( common source ) , output capacitance ( common source ) , reverse transfer capacitance ( common source ) c iss ,c oss ,c rss ( pf ) 012 10 8 26 4 0 120 100 80 60 40 20 ta= ? 25 ? c 25 ? c 75 ? c v ds =5v ta=25 ? c gate to source voltage v gs ( v ) drain current i d ( ma ) 012 10 8 26 4 0 120 100 80 60 40 20 i d =20ma ta=75 ? c 25 ? c ? 25 ? c gate to source voltage v gs ( v ) drain to source on-resistance r ds(on) ( ? ) 0.1 1 10 100 0.3 3 30 0.01 0.03 0.1 0.3 1 3 10 30 100 v o =5v ta=25 ? c output current i o ( ma ) input voltage v in ( v )
please read the following notes before using the datasheets a. these materials are intended as a reference to assist customers with the selection of panasonic semiconductor products best suited to their applications. due to modification or other reasons, any information contained in this material, such as available product types, technical data, and so on, is subject to change without notice. customers are advised to contact our semiconductor sales office and obtain the latest information before starting precise technical research and/or purchasing activities. b. panasonic is endeavoring to continually improve the quality and reliability of these materials but there is always the possibility that further rectifications will be required in the future. therefore, panasonic will not assume any liability for any damages arising from any errors etc. that may ap- pear in this material. c. these materials are solely intended for a customer's individual use. therefore, without the prior written approval of panasonic, any other use such as reproducing, selling, or distributing this material to a third party, via the internet or in any other way, is prohibited. request for your special attention and precautions in using the technical information and semiconductors described in this material (1) an export permit needs to be obtained from the competent authorities of the japanese govern- ment if any of the products or technologies described in this material and controlled under the "foreign exchange and foreign trade law" is to be exported or taken out of japan. (2) the technical information described in this material is limited to showing representative character- istics and applied circuit examples of the products. it does not constitute the warranting of industrial property, the granting of relative rights, or the granting of any license. (3) the products described in this material are intended to be used for standard applications or gen- eral electronic equipment (such as office equipment, communications equipment, measuring in- struments and household appliances). consult our sales staff in advance for information on the following applications: ? special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. ? any applications other than the standard applications intended. (4) the products and product specifications described in this material are subject to change without notice for reasons of modification and/or improvement. at the final stage of your design, purchas- ing, or use of the products, therefore, ask for the most up-to-date product standards in advance to make sure that the latest specifications satisfy your requirements. (5) when designing your equipment, comply with the guaranteed values, in particular those of maxi- mum rating, the range of operating power supply voltage and heat radiation characteristics. other- wise, we will not be liable for any defect which may arise later in your equipment. even when the products are used within the guaranteed values, redundant design is recommended, so that such equipment may not violate relevant laws or regulations because of the function of our products. (6) when using products for which dry packing is required, observe the conditions (including shelf life and after-unpacking standby time) agreed upon when specification sheets are individually exchanged. (7) no part of this material may be reprinted or reproduced by any means without written permission from our company. 2001 mar
|
